Traffic Sign Recognition (TSR) FORScan mod (confirmed working)

[Darnon]

There is no navagation available on the maverick.

There isn't traffic sign recognition available from the factory either, yet here we are. Not impossible someone might swap in an APIM with Nav.

Sponsored

 

[criminosis]

There is no navagation available on the maverick.

Factory provided no, but this was making its way around the forums a while back for what it's worth

https://www.4dtech.com/maverick-22-navigation-upgrade-for-sync-3/

 

[Maverick2022XL]

There isn't traffic sign recognition available from the factory either, yet here we are. Not impossible someone might swap in an APIM with Nav.

Upgrades to the existing Sync 3 on the lariats w/Lux package should be possible. It may already be installed but hidden in the APIM settings. That is for Lariat owners to determine.

 

[bdaniel230]

In short yes but the last 2 digits in the codes are checksums i.e. xxxx-xxxx-xx** where the * is the checksum values. When you put in the changes it will give you a checksum error. That is okay to proceed since forscan will correct them before writing.

Great to hear. After working with networks and checksums all week I really want to stay away from the binary nightmare that is checksum calculations on circuits I don't have the schematic

 

[bdaniel230]

Factory provided no, but this was making its way around the forums a while back for what it's worth

https://www.4dtech.com/maverick-22-navigation-upgrade-for-sync-3/

A nav module for Maverick? That's a grand for a module that will need to be introduced into the ECM through Forscan, Fun.

 

[bdaniel230]

A nav module for Maverick? That's a grand for a module that will need to be introduced into the ECM through Forscan, Fun.

If someone can tell me I can upgrade my non-sync system to any of the sync systems, that would be great. Otherwise I need to wait until a Maverick gets wrecked to find the unit to make mine sync. I had no idea that you had to order the upgrade to get sync

 

[GodFatherofTech]

Got it all enabled. Not only after you do it in Forsan, you have to go into settings and enable it, then turn on the screen.

I guess I am dense. I can't seem to figure out all of the changes needed in easy mode to make this happen.

I have looked at chimes in IPMA and TSR is set to SLOIF. in APIM, I have TSR overspeed enabled.

Unsure what else I might be missing.

 

[GodFatherofTech]

I guess I am dense. I can't seem to figure out all of the changes needed in easy mode to make this happen.

I have looked at chimes in IPMA and TSR is set to SLOIF. in APIM, I have TSR overspeed enabled.

Unsure what else I might be missing.

ok. reading and rereading this thread and I have it working, but with round signs. that's fine until I can sort this out. I have US and MPH selected in IPMA.

Thanks, everyone

 

[TrippMe]

ok. reading and rereading this thread and I have it working, but with round signs. that's fine until I can sort this out. I have US and MPH selected in IPMA.

Thanks, everyone

I THINK there are only round signs.

It works remarkably well.

 

[GodFatherofTech]

I THINK there are only round signs.

It works remarkably well.

A post on FB group shows square signs. So, I am missing something.

 

[belmor]

I think the round signs are showing up on the FX4/Lariat screen and the square ones show up on the XL/Base XLT screen. I haven't seen a fix to make square signs on the larger dash.

 

[Gullzway]

So on a Lariat/Lux to enable TSR I just need to make these two edits?

Enable TSR in Menu:
IPC
720-03-02
xxCx-xxxx

706-01-01
xxxx-xxD3-xxxx

Not interested in No Passing Icon or Over Speed Chime.

 

[GodFatherofTech]

FYI, these signs don't get recognized.

 

[Maverick2022XL]

FYI, these signs don't get recognized.

Then use

706-01-01
xxxx-xxD2-xxxx
instead

706-01-01
xxxx-xxD3-xxxx
is not a valid code for Mavericks then

 

[Maverick2022XL]

A post on FB group shows square signs. So, I am missing something.

The 4 inch clusters show square signs, The 6 inch cluster which shows round signs.

Sponsored