Underbody Cavity Shield Cover: Essential Protection for Your Maverick

[MABETT]

Will this fit the 2025 Maverick LOBO? Is it just the drivers side or both?

This one is designed for the driver’s side. It should fit the 25 LOBO as well.

Sponsored

 

[MABETT]

Question: I am scheduled (6/25/25) to get my Maverick undercoated & rust-proofing. Do you see any problem installing after the undercoating?

That’s totally fine, it won’t affect installation.

 

[MABETT]

What am I doing wrong. All I see is the 8% discount at checkout. No other discount using your link.
f1jim

Sorry for the confusion — I’ve updated the description to clarify. The 8% discount from the link applies on top of the 22% already shown on the Amazon page.

 

[vabchusa]

I have placed my order for the Mabett Underbody Cavity Shield Cover.
Price was $64.39. 30% off of $89.99 should be $62.99.

Item(s) Subtotal: $69.99
Promotion Applied: -$5.60
Total before tax: $64.39

$89.99 - 22% = $69.99

$69.99 - 8% = $64.39

$89.99 - 30% = $62.99

Combined discounts are funky. They took 22% off the $89.99 price first and then the 8% off the already discounted price..

 

[MakinDoForNow]

Combined discounts are funky. They took 22% off the $89.99 price first and then the 8% off the already discounted price..

That's the way stackable discounts work. 15-10-7 would be 100% less 15% then 10% off that reduced price then 7% off that reduced price......

 

[Gray Goose]

On some Mavericks, the structural bolts, indicated by the red arrows, may not be easy to remove. I couldn't get the bolts out even with the help of the largest breaker bar that would fit under there.

 

[ListedGuru]

On some Mavericks, the structural bolts, indicated by the red arrows, may not be easy to remove. I couldn't get the bolts out even with the help of the largest breaker bar that would fit under there.

I picked up my new 25 AWD Hybrid Mav a few weeks ago and have been eyeing this underbody cavity shield and it seems like a good deal at this prince. Most of the install posts I've read have said it's easy to install with the caveat being that the bolts are difficult to remove. I think yours is the first comment I've read that mentions being unable to remove the bolts. Honestly I'm not a fan of having to remove those bolts but I'm also not too keen on keeping that hole wide open either.

If I do decide to order this cavity shield hopefully I can get those bolts loosened as I'll admit I'm not as strong as I once was

 

[vabchusa]

I'm going to use some "FLEX SEAL' tape on mine. I use it on the bottom of my hovercraft and am on year 6 with it.

 

[MABETT]

On some Mavericks, the structural bolts, indicated by the red arrows, may not be easy to remove. I couldn't get the bolts out even with the help of the largest breaker bar that would fit under there.

These are the original factory bolts; some may be loose while others are tight. Over time, they can get a bit stuck and hard to remove. I can help you with after-sales support—I'll send you a DM.

 

[Buggy Man]

On some Mavericks, the structural bolts, indicated by the red arrows, may not be easy to remove. I couldn't get the bolts out even with the help of the largest breaker bar that would fit under there.

I have trouble getting down & up from the floor especially in a confined space. I did the best I could getting these pictures.

Huh, My 2025 LOBO doesn't have the muffler back there.

So, what is that blue "tube" or rod between the two bolts in the frame? Will that get in the way of mounting the panels?
Is the above picture from a hybrid?

 

[Gray Goose]

I have trouble getting down & up from the floor especially in a confined space. I did the best I could getting these pictures.

Huh, My 2025 LOBO doesn't have the muffler back there.

So, what is that blue "tube" or rod between the two bolts in the frame? Will that get in the way of mounting the panels?
Is the above picture from a hybrid?

Very interesting that you don't have a muffler or it's relocated.
In my opinion, if you're having trouble just getting a picture, I would not attempt to install it. Unless you have access to a lift, it requires lying on your back under the vehicle while finagling the parts into place.
If Mabett doesn't reply, direct message them. They have been very helpful with my order.

 

[Backin15]

Your picture looks like what I saw when I looked at mine a few days ago. The shield comes in two pieces and it looks like one has a drop down to clear the silver tube. Mine should be here is a couple days, I will let you know if there are any clearance issues.

 

[Scout27]

Ordered mine today!

 

[TheShark]

Just ordered.

 

[MABETT]

I have trouble getting down & up from the floor especially in a confined space. I did the best I could getting these pictures.

Huh, My 2025 LOBO doesn't have the muffler back there.

So, what is that blue "tube" or rod between the two bolts in the frame? Will that get in the way of mounting the panels?
Is the above picture from a hybrid?

You can click on this thread link to see feedback from 25 owners who have installed it before — it might be helpful for you.
https://www.mavericktruckclub.com/f...avity-shield-covers-just-arrived.59568/page-4

Sponsored