Lane Keeping System retrofit install using FORScan (on all trims without Copilot 360)

[DanielNKR]

Hello, first time here, from Brazil.

2.OT Lariat FX4 Lane Keeping, Sport & Eco modes and TSR working here.

Thank you!!

Sponsored

 

[801Maverick801]

I know this is a big ask but after going through this thread I am pretty confused and just hoping someone will give me codes specific to my truck.

XLT Ecoboost w/ FX4, tow package, luxury package with Inverters. 6 inch screen. No Co-pilot.

So much thanks in advance if someone pulls through.

 

[atldump]

this works on a 2023, and 2024s?

 

[Eagle11]

this works on a 2023, and 2024s?

2024's haven't been delivered, so how can anyone answer that

 

[Vtec87pr1]

I did but having issues with the steering controls . Any suggestions

Nvm found the problem thanks . Good write up.

 

[jdmz]

I know this is a big ask but after going through this thread I am pretty confused and just hoping someone will give me codes specific to my truck.

XLT Ecoboost w/ FX4, tow package, luxury package with Inverters. 6 inch screen. No Co-pilot.

So much thanks in advance if someone pulls through.

Did you ever figure this out? I have same configuration. Original post is talking about a smaller screen and we have a bigger screen with our FX4.

 

[TrailMaster]

Did you ever figure this out? I have same configuration. Original post is talking about a smaller screen and we have a bigger screen with our FX4.

∆ BUMP ∆

I'm curious about this as well. The title does say all trims without copilot, but I'd sure like to be sure it'll work with FX4 screens (without copilot). Can anyone verify this is working with the 6" FX4 screen?

 

[jdmz]

∆ BUMP ∆

I'm curious about this as well. The title does say all trims without copilot, but I'd sure like to be sure it'll work with FX4 screens (without copilot). Can anyone verify this is working with the 6" FX4 screen?

I got it to work with speed sign recognition. 2023 XLT ecoboost fx4 4k tow.

Followed the snowkarver guy's post on page 10 using as built data. Use the asbuilt values over this thread and override some of what this thread has for the conflicting values in the speed sign recognition if you want that.

 

[youmax]

Hi, anyone know wich pins have contact to button of lane keeping?

 

[Angel1221]

I followed the codes for the ecoboost and now have a trailer brake module fault, any help?

 

[Angel1221]

Hello All ....
I ran into a small snag after "retro-Fitting" the TSR and Lane Keep mod ...
I'm getting a "trailer brake module fault" at startup ... I don't have trailer tow package on my truck so i'm thinking that during the programming a value got flipped to look for the trailer brake controller. Any ideas welcome

--->Kevin

2023 XLT No Lux -- Black appearance pkg.

Did you ever find a fix? I am having the same problem

 

[Hook401]

Actually no ... I just did the TSR Mod for speed signs ... I have a bit of time to poke at it again this weekend and see if i can get it going .... do you have the tow package or not ?
--->Kevin

 

[Wonderwall]

SCCM
The middle part of the code specifies you have the lane keep left turn stalk installed the other lines refer to the steering wheel buttons.
724-02-01
1228 A820 3060
Steering wheel buttons w/o cruise control, switch combo SW8588 / SW8589

1258 6820 3050
steering wheel buttons w/ cruise control, switch combo SW8576 / SW8579

I have the correct turn signal stalk installed. What exactly is meant by switch combo? I attempted to program mine today everything was going ok until I got to this section. I have an XLT with cruise control buttons on the wheel. When I entered 1258 6820 3050 and tried to write it said there was a checksum error. At this point I got worried. Checked, double checked, triple checked I had the correct numbers but still kept getting the same message. Any help much appreciated.

 

[Darnon]

I have the correct turn signal stalk installed. What exactly is meant by switch combo? I attempted to program mine today everything was going ok until I got to this section. I have an XLT with cruise control buttons on the wheel. When I entered 1258 6820 3050 and tried to write it said there was a checksum error. At this point I got worried. Checked, double checked, triple checked I had the correct numbers but still kept getting the same message. Any help much appreciated.

Checksum errors aren't uncommon. You should just be able to tell it to proceed and FORScan will calculate the proper checksum entry automatically.

 

[Wonderwall]

Checksum errors aren't uncommon. You should just be able to tell it to proceed and FORScan will calculate the proper checksum entry automatically.

Thanks for the quick response. It was my first time using Forscan and was super nervous. Will try again tomorrow.

Sponsored