Sync4 APIM and 13.2" Screen Installation Guide (Lariat Models)

[RONR11]

Here's the backside with the tray installed. It's really not terrible

Looks good to me, great job guys

Sponsored

 

[shazel]

No no didn't need to modify anything else but the apim programing. There's a few dtcs stored. But nothing that trips a light . I can share it but it's specific to my truck. Like I said originally every truck is different

I have sync 4 on the 8 inch screen in my truck now. I will be swapping to the 13 inch screen eventually when I can find the parts. Even though every truck is different, I would like to compare asbuilts to speed up installation.
Thanks

 

[Billzilla15]

I have sync 4 on the 8 inch screen in my truck now. I will be swapping to the 13 inch screen eventually when I can find the parts. Even though every truck is different, I would like to compare asbuilts to speed up installation.
Thanks

this is my current working as built. enjoy


Module=7D0 (APIM - Accessory Protocol Interface Module (SYNC))

01-01 A085 0A00 8088
01-02 0000 D609 00B9
01-03 C390 0020 0C5A
01-04 02E0 8080 00BE
02-01 0722 000F 283A
02-02 C000 00D0 60CB
02-03 A040 1001 00CD
03-01 5553 0B04 099B
03-02 0300 0605 00EA
03-03 0901 0000 00E7
04-01 4578 0078 0011
05-01 0004 2800 0009
05-02 0102 00CF DA8A
05-03 4BE7 0000 0011
06-01 1874 18C4 296F
06-02 AE8D
07-01 1500 3300 0027
07-02 0000 5EA1 00DF
07-03 0056 5681 000E
07-04 886A
08-01 CE00 0001 00AF
08-02 0000 0000 00E1
09-01 03A8 AC70 18C0
09-02 0033 0000 182D
09-03 0033 0000 0016
09-04 0240 0000 E006
09-05 2014 0000 2039
10-01 0000 0000 00E8
10-02 0000 0000 00E9
10-03 0000 0000 08F2
10-04 0000 0000 00EB
10-05 0013 E000 00DF

 

[pantera156]

Here's the backside with the tray installed. It's really not terrible

It's great!
Did you cut the back cover?
Can you upload a photo of how it looks from the front?
I plan to do the same. But the screen is very expensive.

Very thanks!

 

[Billzilla15]

It's great!
Did you cut the back cover?
Can you upload a photo of how it looks from the front?
I plan to do the same. But the screen is very expensive.

Very thanks!

No cutting just heat to massage the plastic around the bold used to mount the screen. Picks are on the first page

 

[axl_rose]

Amazing work!

 

[pantera156]

https://www.ebay.com/itm/2667703514...UIdv2f39NsMHHX3IJYZobfAnNA==|tkp:BFBMnq-ntq5k

Much cheaper screen, but without the frame.

 

[Billzilla15]

https://www.ebay.com/itm/266770351482?_nkw=ford+12"+screen&itmmeta=01J5SP9TY6CD4S7FJGTGYCDB3V&hash=item3e1cc0857a:g:hX0AAOSwvvNmHSTq&itmprp=enc:AQAJAAAA8HoV3kP08IDx+KZ9MfhVJKlD+SUGmC0TQkroif0D+eqGpIAvoLgAp0h2yu3oG1CYb5MHW0cqITnZHGQu0780Q4xLPGIE/rLILnb1yiaFZrmZN58rMUbFkGChHBtJTeNRpRnI8/UIWfODQLsL73v6X5c8EZVSNvnZpr28gsoXimuZtgh1LRxCnqrairuqWGXOqgQlX2yuwjx14de/YBXi+nJqOvlZDNNadi6qwi9+gk1IMidI0kxg2g6eHyv9U1DH30zOq5+NofILYfGcM/Onzk3Co61Eh0j2jLOJAaMqUIdv2f39NsMHHX3IJYZobfAnNA==|tkp:BFBMnq-ntq5k

Much cheaper screen, but without the frame.

It's smaller too. Mines 13.2 inches not 12. That ones also going to need some very custom mounting

 

[colinl]

It's smaller too. Mines 13.2 inches not 12. That ones also going to need some very custom mounting

the 12" screen is used in the Bronco and F-150, maybe other models now. they got it before the Escape (and now Maverick) got the 13.2".

edit: and you're right, the mount is completely different in those vehicles for the 12". they are inset in the dash, and have trim all around. they don't sit on top like the Escape and Maverick 13.2".

I would not try to adapt a 12".

 

[pantera156]

the 12" screen is used in the Bronco and F-150, maybe other models now. they got it before the Escape (and now Maverick) got the 13.2".

edit: and you're right, the mount is completely different in those vehicles for the 12". they are inset in the dash, and have trim all around. they don't sit on top like the Escape and Maverick 13.2".

I would not try to adapt a 12".

The only way would be to print parts on a 3D printer. But it will be very difficult to make the design...

 

[Dmat]

The only way would be to print parts on a 3D printer. But it will be very difficult to make the design...

A guy on facebook actually demo'd his 3d printed screen housing that centered the screen.
This might end up becoming a base for a 10 or 12" screen if he releases the cad files.

 

[pantera156]

A guy on facebook actually demo'd his 3d printed screen housing that centered the screen.
This might end up becoming a base for a 10 or 12" screen if he releases the cad files.

Great idea! Would you be so kind as to ask for the CAD files?
The truth is that the 12" screen is much cheaper!

 

[Dmat]

Great idea! Would you be so kind as to ask for the CAD files?
The truth is that the 12" screen is much cheaper!

I did already. They guy said he might when he likes the finished product.

 

[pantera156]

I did already. They guy said he might when he likes the finished product.

We have to wait then

 

[pantera156]

I found another better option. The Ford Transit 12" screen
I think it looks more or less like the drawing I made in Paint

https://www.ebay.com/itm/1964935694...lp:2332490&itmmeta=01J6D3F2CVGRN1EHD55Q25PTWC

Sponsored