Sync4 APIM and 13.2" Screen Installation Guide (Lariat Models)

[pantera156]

Did you have to buy the USB plug extender? Blue plug

I didn't buy it, but I think I can make one.

Sponsored

 

[pantera156]

And we are up! Couple issues I’ve run into now though. The back up camera works, but is acting up a bit? Incredibly dim.

And then there’s the fun of reprogramming thing. I couldn’t figure out how to get the volume to display properly (stuck on 0) but did get climate controls to display. Also can’t figure out how to get the splash screen to full screen again.

The same thing happened to me before programming. After programming the volume it stops marking 0

 

[pantera156]

Looks great! I’m ready to do this swap as well just not sure exactly what needs to be changed in forscan.

Did you copy Bills as-built from earlier in this thread, or what needs to be changed? Didn’t see any other programming suggestions. I’m using the 12” and apim from a transit

thanks!

I used the programming that is at the beginning of the post.
But I can't say yet that everything works 100%

Thanks!

 

[pantera156]

You got sound?

can you share the coding? Txs

Did you connect the climate controls?

I tried without the controls and the radio didn't work.
After connecting the climate control it worked.

I used the codes that are at the beginning of the post.

 

[jonly2468]

I didn't buy it, but I think I can make one.

I see you have a gps antenna? Did you need that to get factory nav working?

part number for the antenna?

 

[pantera156]

Does anyone know what the other connectors are for?

Thanks!

 

[jonly2468]

Does anyone know what the other connectors are for?

Thanks!

Was wondering the same thing… possibly for the 360* cameras? Would be really cool to figure those out

 

[pantera156]

I see you have a gps antenna? Did you need that to get factory nav working?

part number for the antenna?

I think it's this antenna.

https://www.ebay.com/itm/353865070119

It is a simple GPS antenna.

 

[pantera156]

Was wondering the same thing… possibly for the 360* cameras? Would be really cool to figure those out

The brown connector is an antenna connector. I don't know what the other one is.

 

[801Maverick801]

So my screens alive. Music quality sounds great. My backup camera is not working though, screen just goes black and then says reverse camera not available. I'm hoping it's a programming thing?

Tomorrow I will get it mounted and hopefully start with the Forscan.

 

[Billzilla15]

So my screens alive. Music quality sounds great. My backup camera is not working though, screen just goes black and then says reverse camera not available. I'm hoping it's a programming thing?

Tomorrow I will get it mounted and hopefully start with the Forscan.

Yes that's programming. I fought with that for a while. I basically killed off everything that had to do with cameras and turned them on one by one till I got mine working

 

[Billzilla15]

Did you need to add an antenna for the factory nav to work?

I did not. But I have a lariat

 

[yeahiguessman]

Do we have any idea what pins on the harness communicate with the audio module for the speaker system? My audio sounds really good 98% of the time. I’m getting the occasional static pop about two to three times a song always at random points. Ideas?

 

[RONR11]

 

[yeahiguessman]

Pin 8?

My assumption is my audio bugs have to be a result of the harness since they didn’t exist before. Though the Sync3 APIM did have an issue of the occasional audio skip. This is more of a very soft static pop. Almost like a record with a little dust. Two to three times a song.

Unsure if it’s harness, APIM, or software at the moment. Maybe I’ll reset the audio module?

Am using the B&O system on the Lariat which I don’t think would cause an issue?

Sponsored