Screenside Dash Cubby Dimensions?

[dogie rider]

Would someone who has gotten their Maverick please provide accurate dimensions for cubby. Thanks

Updated with dimensions / measurements by @Delzona

Sponsored

 

[SgtLip]

Would someone who has gotten their Maverick please provide accurate dimensions for cubby. Thanks

#33

 

[dogie rider]

I would like something more accurate so I can build a custom insert/drawer that would fit snugly in it.

 

[SgtLip]

I would like something more accurate so I can build a custom insert/drawer that would fit snugly in it.

@dogie rider
Sorry. I've seen 2 or 3 posts with a tape measure. Best you'll get before getting your Maverick to use your own tape measure on.

 

[dogie rider]

You may be right, but I'm hoping someone else may have plans similar to mine.

 

[Delzona]

I would like something more accurate so I can build a custom insert/drawer that would fit snugly in it.

I have some pictures of the cubby with tape measure that can give an idea of the dimensions, however because the cubby tapers down towards the back I wasn't able to an accurate measurement. If you want the pictures just let me and I can either post them or PM them to you.

 

[dogie rider]

I have some pictures of the cubby with tape measure that can give an idea of the dimensions, however because the cubby tapers down towards the back I wasn't able to an accurate measurement. If you want the pictures just let me and I can either post them or PM them to you.

I appreciate the offer, but I don't think that will give me what I need. I want to build something that fits snugly in the hole, so I may need to wait until I get my truck as SgtLip said.

 

[sabar]

Dimensions are difficult on it because it is an odd shape, with lots of angles and bevels. My tentative dimensions with my calipers are: 57mm width, 84mm height, 75-78mm depth (tapers from bottom to top on a concave radius from feeling around in there).

I hope to have better dimensions of the cubby after some trial/error 3d prints. I don't have the tooling to measure this precisely (you'd need a good set of gauges).

 

[Delzona]

Dimensions are difficult on it because it is an odd shape, with lots of angles and bevels. My tentative dimensions with my calipers are: 57mm width, 84mm height, 75-78mm depth (tapers from bottom to top on a concave radius from feeling around in there).

I hope to have better dimensions of the cubby after some trial/error 3d prints. I don't have the tooling to measure this precisely (you'd need a good set of gauges).

Looking forward to seeing what come up with.

 

[dogie rider]

Dimensions are difficult on it because it is an odd shape, with lots of angles and bevels. My tentative dimensions with my calipers are: 57mm width, 84mm height, 75-78mm depth (tapers from bottom to top on a concave radius from feeling around in there).

I hope to have better dimensions of the cubby after some trial/error 3d prints. I don't have the tooling to measure this precisely (you'd need a good set of gauges).

Thanks a lot for the measurements! That gives me a much better idea of where to start. I look forward to seeing your updated dimensions.

 

[sabar]

Small update -- 57mm x 85mm nearly perfectly fits the front. I'll mess with some slightly larger prints to see what a good depth is.

 

[dogie rider]

Small update -- 57mm x 85mm nearly perfectly fits the front. I'll mess with some slightly larger prints to see what a good depth is.

Thanks!

 

[Spot]

Thanks!

I'm really curious as to how this project is going.

I plan on 3D printing a coin drawer that is similar to what I have in my Audi now. The Audi drawer is 20mm tall, and the length & width of what you are mentioning seems reasonable to work with. With the remaining height, I may be able to build a second drawer or just leave the rest as a doored cubby.

At any rate, if you could post your status on this, I would certainly appreciate it.

 

[Tundra2Maverick(?)]

I'm really curious as to how this project is going.

I plan on 3D printing a coin drawer that is similar to what I have in my Audi now. The Audi drawer is 20mm tall, and the length & width of what you are mentioning seems reasonable to work with. With the remaining height, I may be able to build a second drawer or just leave the rest as a doored cubby.

At any rate, if you could post your status on this, I would certainly appreciate it.

Any updates? So far I have seen a Kleenex Holder and Phone Mount in the cubby. I would prefer a drawer or door as described above.

 

[bombast]

Any updates? So far I have seen a Kleenex Holder and Phone Mount in the cubby. I would prefer a drawer or door as described above.

I want to make a little coin tray for in there as well. I got a cardboard template cut that seems to be the right size. Modeling a flat plate in TinkerCAD now, will have it printed at work on Wednesday. If its accurate, I'll try to update this thread then.

Problem seems to be it tapers on both sides at different degrees. My current template only tapers on one side - Hoping that's enough to get a tight fit. Whoever drew the dimensions for this thing at Ford is a dick.

Sponsored