2.0l engine appearance cover installed - part numbers

[felsf50]

These are the parts I ordered and installed. The cover is a hard dense foam. 812D is a bolt that screws into the brass threaded insert it the top left. It tightens down after the cover is installed. 957A is the bottom right bolt with a bulb like head that screws into the brass threaded insert and snaps into the cover when installed. 812D gets screwed in after 957A.

My ears say that engine noise is reduced as witnessed inside my garage. But that doesn't matter to me as "I" like the look. Your opinion may differ but does matter to me or others that like it

K2GZ*6A949*A​	Engine Cover​	1​	​	​
AG9Z*00812*D​	Engine Valve Cover Grommet​	1​	​	​
AV6Z-6A957-A​	Engine Cover Stud​	1​	​	​

Sponsored

 

[vezpa]

Is there only 1 bolt holding the cover down or do we need multiples of
AG9Z*00812*D & AV6Z-6A957-A ?

Thanks

 

[Brian_J]

"I" like the look.

​
				​

let’s see it! Pictures!

 

[felsf50]

Is there only 1 bolt holding the cover down or do we need multiples of
AG9Z*00812*D & AV6Z-6A957-A ?

Thanks

1 each. There are two studs already in the engine compartment

 

[felsf50]

I like the look! You opinion may vary..

 

[felsf50]

let’s see it! Pictures!

Posted pic

 

[Jah.]

What was the cost ?

 

[BlueSnake77]

Well good luck on getting one. I ordered from a parts dealer on line the beginning of December and got tired of waiting so I canceled it a couple of days ago. Seems they are back ordered at the manufacturer. They are about $100 on average. You may find a dealer on Ebay or such that has one in stock, just make sure it's ACTUALLY in stock by contacting them. You know how some of these places are. They say they have something and then after you order it they tell you it's not in stock and they have to get it from the manufacturer.

 

[kcamp317]

That looks good.

 

[Guv]

I have a couple from a 5.7 HEMI, free. These are usually the first thing I throw over the back fence.
Sorry for being a bugger.

 

[XLent]

Well good luck on getting one. I ordered from a parts dealer on line the beginning of December and got tired of waiting so I canceled it a couple of days ago. Seems they are back ordered at the manufacturer. They are about $100 on average. You may find a dealer on Ebay or such that has one in stock, just make sure it's ACTUALLY in stock by contacting them. You know how some of these places are. They say they have something and then after you order it they tell you it's not in stock and they have to get it from the manufacturer.

Got mine from Tasca.
good service

 

[Gary patrol]

These are the parts I ordered and installed. The cover is a hard dense foam. 812D is a bolt that screws into the brass threaded insert it the top left. It tightens down after the cover is installed. 957A is the bottom right bolt with a bulb like head that screws into the brass threaded insert and snaps into the cover when installed. 812D gets screwed in after 957A.

My ears say that engine noise is reduced as witnessed inside my garage. But that doesn't matter to me as "I" like the look. Your opinion may differ but does matter to me or others that like it

K2GZ*6A949*A​	Engine Cover​	1​	​	​
AG9Z*00812*D​	Engine Valve Cover Grommet​	1​	​	​
​ AV6Z-6A957-A​	Engine Cover Stud​

 

[Gary patrol]

seems like this cover is very hard to get, where did yours, I have tried several Ford dealership web sites they take my orders but then tell me its discontinued,,,, thoughts please

 

[dalola]

I like the look! You opinion may vary..

Who would think the mass of wires & tubes looks better than this??

 

[Nw_adventure]

Th

Who would think the mass of wires & tubes looks better than this??

The open port and stud- upper left bug me but otherwise yes its better than the uncovered rats nest -

Sponsored