Fordsync4 Buyers remorse - DIY Coming Soon for Sync 4 conversion

[Redneck Garage]

Did a video on my problems with the fine folks at Fordsync4 and their customer service and products. They have offered me $$$ to take the video down here's a quote -

Hello David,

Sorry about the late reply.

We apologize for the inconvenience caused by our service, we did pre-program the module based on the F150 data, if you need programming service our technicians can provide you with remote programming service, but your video will have a great impact on our website, Can we negotiate how we can take down this video?
Sorry again.
______________________
Thank you&Best regards,
Vency Lee
Fordsync4 Team

Hahahahaha NO WAY !!!!! I would rather loose money and spread the truth about these scammers than to take their money to be silenced !!!!

Sponsored

 

[24atlasmaverick]

I knew I had to run away when I tried to call their support number and it went to a busy signal. Good info for those who don’t know! Now if someone would make a p&p sync 3 kit for XLT’s!

 

[Redneck Garage]

Terrible company or maybe just some lonely Chinese dude - dont know LOL After I told them It wasn't programmed - no reply back then.

 

[Toddman45]

Nothing worse than poor product support or customer service. Especially when spending a good chunk of change on a product.

 

[Redneck Garage]

I knew it was going down hill hahaha we started at 1999.00 then they offered 500.00 off for Maverick Truck Club Members then after buying and not getting any answers I told them I was cancelling and calling my bank. They begged me to not cancel and they would give me 200.00 more off and I said 300 and finally they refunded 300 so I had 1200.00 total in it. Ill sell the kit and or parts - yes some lost money but not near as much as the 2K price lol .

 

[flyswatter]

You're doing God's work David.

 

[pantera156]

I knew it was going down hill hahaha we started at 1999.00 then they offered 500.00 off for Maverick Truck Club Members then after buying and not getting any answers I told them I was cancelling and calling my bank. They begged me to not cancel and they would give me 200.00 more off and I said 300 and finally they refunded 300 so I had 1200.00 total in it. Ill sell the kit and or parts - yes some lost money but not near as much as the 2K price lol .

Will it be possible to programer it?

 

[Redneck Garage]

Will it be possible to programer it?

Oh for sure I have the builds ( config data ) Im testing from multiple sources. This APIM is a 12" Ford F150 and cannot do a 13.2 escape screen. The 2023 APIM made for the 13.2" screen can do a 12" screen However.

 

[Redneck Garage]

You're doing God's work David.

Thank you - now they are trying to pay me to take the video down !!!!! 8 Days after I emailed them telling them it wasn't programmed correctly and I need the data to do it myself.

Hello David,

Sorry about the late reply.

We apologize for the inconvenience caused by our service, we did pre-program the module based on the F150 data, if you need programming service our technicians can provide you with remote programming service, but your video will have a great impact on our website, Can we negotiate how we can take down this video?
Sorry again.
______________________
Thank you&Best regards,
Vency Lee
Fordsync4 Team

Yeah - That IS the point to have an impact on their website AND to warn others how shady they are ..... Duh.

 

[Justin says...]

I knew I had to run away when I tried to call their support number and it went to a busy signal. Good info for those who don’t know! Now if someone would make a p&p sync 3 kit for XLT’s!

I believe someone made a DIY on how to do it, including how to make the harness. But, I think he was a doctor or something and it seemed difficult to do. If I had the time, I'd figure it out and make 20 or 40 of them and sell them here. Somebody should!

 

[Redneck Garage]

Im going to have a video on how to do the harness - it really isn't that hard once I figured it out. Billzilla15 gave a great amount of info but sometimes a video is easier to follow.

 

[RONR11]

Im going to have a video on how to do the harness - it really isn't that hard once I figured it out. Billzilla15 gave a great amount of info but sometimes a video is easier to follow.

Any idea when you will make video? Been tinkering with this also txs Ron

 

[Redneck Garage]

Been working on it should be done this week

 

[Samcat13]

Been working on it should be done this week

Thank you. Will wait for next video.

 

[pantera156]

Oh for sure I have the builds ( config data ) Im testing from multiple sources. This APIM is a 12" Ford F150 and cannot do a 13.2 escape screen. The 2023 APIM made for the 13.2" screen can do a 12" screen However.

Good luck with it.
I bought all the parts separately. I'll have them all by December.
The black plastic that the Chinese sent you is to cover the excess space. It is the only thing that cannot be bought separately.

Sponsored