Search results

Does the Tee harness go in the dome light? That light's voltage depends on brightness adjustment I seem to remember.

I used a nylock upside down for the bottom nut and just tightened the top nut on. I could have used a belleville lockwasher on top of the ring lug but didn't. so far haven't seen any loosening.

The front marker lights and the ambient air temperature harness is fed from connector that's just in front of right wheel well. Maybe or not related to the accident if the harness feeding that had some damage?

Most of the jump posts have been 5/16-18 threads. Maybe some have been metric. I used 2 nuts and a ring lug. High enough to run the wire out the side. I did put a little notch in the cover, only needed it on right side but cut 1st notch on left by mistake.

For steering wheel switch I watched this video: Ford Maverick Cruise Control

Bumper cover removal is probably about same as earlier models besides around the headlights. http://testdriven.tv/2023/03/ford-maverick-raptor-style-grille-installation/ Since the CCM mounts below I'd guess don't have to do anything with the grille.

C3512A is 12V Power, Ground for the media hub. C3512B = USB Data Lines

My old legs & back was my main reason for getting this done. Writing it down will make it easier for me to remember the details of what I did a few months from now.

PINPOINT TEST B: THE AC OUTLET LED (LIGHT EMITTING DIODE) INDICATOR IS NEVER ON Possible Causes • Fuse(s) • direct current/alternating current (DC/AC) inverter • AC Outlet • Wiring, terminals or connectors Visual Inspection and Pre-checks • Verify the BCM Fuse 6 (10A) is OK. • Verify the BJB...

Ford's MSW inverter is nearly a square wave.

2025 Parts lookup makes it look like 4 for front. Maverick 2.5L I4 Electric CVT 4x4 Lariat SuperCrew w/ Navigation 2025 Parking Distance Control Sensor - Parking Aid System. Part Number: NU5Z-15K859-AQPTM Supersession(s): NU5Z 15K859AQ; NU5Z15K859AQ; NU5Z15K859AQPTM Fits Bronco, Bronco Sport...

@EffNo50 @Gaidheal The heat pads are connected in series so adding a resistor to one pad would reduce current through both pads I think. The seat pad has the temperature sensor. If it doesn't send feedback to the HVAC module, the pads don't heat up. I saw this when removing the NTC wires...

Disconnect 12V battery. Work the body harness ty rap fir tree mount out of bottom of seat. Disconnect the seat connector. Have to press on the release lever and takes some force to separate the connectors. (Can work loose the fir tree loose & disconnect once seat bolts are out and tilt the seat...

Ford heat pads (elements) for Driver & Passenger front seats. (Fairwayford.net) Seat Cushion Heater - Ford (NZ6Z-14D696-A) Seat Back Heater - Ford (NZ6Z-14D696-B) HVAC Module from a Maverick XLT with Lux Package Seat heating pads harness with Yazaki male connectors, 4-Pin, 2-Pin HVAC module to...

I was looking at connectors for different reason than speakers. Looking at the audio wiring diagram, looks like Front Right goes thru C207 the connector on RH Kick panel. It's the RH one of the 2 on that bracket. C207 Front Left looks like it's on C201 the lower one under the dead pedal.

For the left front trim. It has a screw where the seat bolts to floor and screw from behind. But maybe something else in the track is worn/loose.

Checked my Renogy 2000W Inverter for a few minutes with a 1500W (12 Amps AC) space heater load. 51A at the 12V DC/DC connection when started the Maverick w/o inverter load. 1500W Space Heater Load: 108A Amps DC into the Renogy 135A DC from the Maverick's 12V DC/DC Converter connection at the...

What soldering iron do you have?

2025 Maverick uses a newer OBDII protocol? https://www.mavericktruckclub.com/forum/threads/scangauge-3-in-a-2025-xl-no-connection-issue-solved.64497/ "the new WWH-OBD protocol found on the 2025 - present Ford Maverick and can be used on other newer Fords that also this protocol." Wonder if...

Updated ones per this thread: '23 Hybrid CV Axles - Ordering - Part # Confusion