Maxzina-Maverick Hood Insulation Mat Available Now!Up to 20% Off

[Justin says...]

I'm interested to read the reviews from some of our members once they receive them. But in general I would pay a little bit more for the higher quality version. We'll just see what the reviews have to say.

Sponsored

 

[Maxzina]

Our soundproof insulation hood mat is temporarily out of stock. But we have already sent the relevant inventory again. If you still have any needs, you can wait until our second batch of goods arrives and purchase again.At that time, we will still provide everyone with the same discount.

 

[FischAutoTechGarten]

Received mine and installed it. Immediately dropped the 2 square 5mmx12mm push pins that go front and center. Looked everywhere. Quick trip to AutoZone to buy 4 more ( so I can drop 2 more).

Fit is good .

 

[Glen Baker LLC]

Nice

 

[TrailMaster]

I'm interested to read the reviews from some of our members once they receive them. But in general I would pay a little bit more for the higher quality version. We'll just see what the reviews have to say.

^ THIS ^

I'm also eager to hear some feedback from purchasers, specifically regarding sound insulation.

 

[EffNo50]

Received mine and installed it. Immediately dropped the 2 square 5mmx12mm push pins that go front and center. Looked everywhere. Quick trip to AutoZone to buy 4 more ( so I can drop 2 more).

Fit is good .

Glad to hear it fits well. Have you noticed any reduction of engine noise? That's what we are all eager to know

 

[Dad]

Glad to hear it fits well. Have you noticed any reduction of engine noise? That's what we are all eager to know

Yep, that's the $60 question.

 

[FischAutoTechGarten]

You know... I should have downloaded one of those decibal apps for my cell phone and performed before/after tests.

Unfortunately, I drove it for about 5 minutes today... and was distracted and forgot to pay much attention to the difference in noise.

I'll pay more attention next time I drive. The coverage is minimal, literally an area above the engine, tranny and fans.

I will add that when I came home after that 5 minute drive.. It did occur to me to check on the alternative square push pins that I had to substitute for the lost 5cmx12cm ones that come with the kit. They were fine. All 8 attachment points were still snug. I know a 5 min drive that doesn't exceed 45mph isn't that helpful.. bit it's something to report on...

 

[A.Bursell]

I installed this on my truck. Fit is definitely good- pretty much looks factory. I am not a fan of the bolts with the metal bar attached- I actually put a piece of heat shrink on each metal bar before installing just to make myself feel a little better about "clamping" to the hood.

No sound readings, but I almost feel like some of the higher pitched engine noise is gone and you just hear the lower pitches. Absolutely could be just in my head. Mine is a Lariat so already have more sound deadening plus I have the foam engine cover added as well.

 

[Maxzina]

I installed this on my truck. Fit is definitely good- pretty much looks factory. I am not a fan of the bolts with the metal bar attached- I actually put a piece of heat shrink on each metal bar before installing just to make myself feel a little better about "clamping" to the hood.

No sound readings, but I almost feel like some of the higher pitched engine noise is gone and you just hear the lower pitches. Absolutely could be just in my head. Mine is a Lariat so already have more sound deadening plus I have the foam engine cover added as well.

Thank you for your evaluation and feedback.

 

[A.Bursell]

Thank you for your evaluation and feedback.

One other piece of feedback/info for anyone installing these. Instead of the included screwdriver, I used a 10mm nut driver. No need to torque them like crazy, but I find a standard size nut driver much easier to use than a small screwdriver.

 

[JPinPA]

I (mostly) installed mine on August 29th - the day it arrived. I say mostly because I can’t get the the two center clamps at the back of the hood to stay engaged long enough to tighten everything up! Left feedback at Amazon regarding the same thing.

what is the trick to getting those oval plates to stay in position (perpendicular to instead of in line with) with the hood slots?

 

[A.Bursell]

I (mostly) installed mine on August 29th - the day it arrived. I say mostly because I can’t get the the two center clamps at the back of the hood to stay engaged long enough to tighten everything up! Left feedback at Amazon regarding the same thing.

what is the trick to getting those oval plates to stay in position (perpendicular to instead of in line with) with the hood slots?

It took me a couple tries to get them in good - and still not entirely pleased with the fit, but seems to be holding. Don't expect them to be perpendicular, just that they are off to the side enough to grab the hood. I found that kind of pushing them up so the bolt is more vertical than at the 45 degree angle it seems like it should be helped. I would also prefer them be more perpendicular and feeling like they are grabbing better, but not sure it's possible.

 

[asylus]

Maxzina-Maverick Soundproof Insulation Hood Mat-Effectively isolate noise

Hello everyone,our soundproof insulation hood mat is in stock.Pls click the link to obtain.The link will be effective at 03:00 am Aug 24th.It has a 20% coupon.The page has a 5% coupon.Only $56.99
https://www.amazon.com/promocode/A2...B320D8FBFC8590_afap_abs&ref_=aa_maas&tag=maas

Discount Period:From 08/24/2024 at 03:00AM to 09/22/2024 at 23:59PM PDT.

Price:$56.99=20% Discount Code (20W3344K)+5% coupon


Feature:

1. PET Felt, very stable, abrasion-resistant
2. Use the screws and snaps for installation

Do you guys have any plans in the works to make sound deadening wheel well liners?

 

[fossil]

Do you guys have any plans in the works to make sound deadening wheel well liners?

Curious, how do you expect the Ford plastic felt to differ from the Maxzina plastic felt?
I'd be down for smooth plastic liners.

Sponsored