DIY - Molle Panel Behind Back Seat

Thex · Nov 23, 2025

I was hoping to find a third party molle panel that was designed to fit behind the back seat. I never found anything so I went the DIY route with 1/2" plywood.

I used the existing mounting holes for the BO amp - (that my XL does NOT have

)

I designed and 3d Printed the brackets for the cases to sit on. The straps are used to just hold then against the panel.

Ford Maverick DIY - Molle Panel Behind Back Seat PXL_20251123_163348621

Ford Maverick DIY - Molle Panel Behind Back Seat PXL_20251123_163421234

Ford Maverick DIY - Molle Panel Behind Back Seat PXL_20251123_163546364

Angmar · Nov 24, 2025

PLA, PETG, or ABS or other?

Thex · Nov 24, 2025

PETG. Both the brackets and the black and purple toolbox

Bobby Chapman · Nov 24, 2025

Does the rear seat still lock in with this equipment behind it

Escapologist · Nov 24, 2025

How far off is my eyeball? Gonna guess about 28"x16" , 1.5" holes on 3"ish centers?

Little boy blue · Nov 24, 2025

Angmar said:
PLA, PETG, or ABS or other?

I love it nice looking job on your setup

Alfetta159 · Nov 24, 2025

I'm not sure what your trim level is, so I imagine that you don't have a subwoofer back there?

Thex · Nov 24, 2025

Bobby Chapman said:
Does the rear seat still lock in with this equipment behind it

yes it does.

Thex · Nov 24, 2025

Escapologist said:
How far off is my eyeball? Gonna guess about 28"x16" , 1.5" holes on 3"ish centers?

24"x12" - 1 1/2" Dia.

Spacing varies as I had to work around the mounting holes.

Thex · Nov 24, 2025

Alfetta159 said:
I'm not sure what your trim level is, so I imagine that you don't have a subwoofer back there?

As stated - "no BO woofer as I have an XL"

Escapologist · Nov 24, 2025

Thex said:
24"x12" - 1 1/2" Dia.

Spacing varies as I had to work around the mounting holes.

Thanks, yeah I put an ish in there since I saw that that was the case.

I think the Lariat here is only gonna take half that, Baltimore and Ohio got all their swtichgear in there or something

come to think of it, the locker sized pegboards or bottom sitting bootracks might be in the ballpark.

Cancunbadlands · Nov 24, 2025

Looking sharp

RR - All the way · Nov 24, 2025

Nice job. Now understand, I have been called lazy quite a few times. I, sometimes, think lazy can also be efficient. Somehow, my laziness would have led me to only drill enough holes in the known locations where straps were needed. Lots of empty holes!! :crazy:

Yes, I am perhaps lazy. Of course, you now have future options if the size of what you are attaching changes........... But those are the kind of bridges a lazy man crosses if needed!

I guess you need a lot of holes for it be called a molle????

Marshall · Nov 24, 2025

Thex said:
I was hoping to find a third party molle panel that was designed to fit behind the back seat. I never found anything so I went the DIY route with 1/2" plywood.

I used the existing mounting holes for the BO amp - (that my XL does NOT have )

I designed and 3d Printed the brackets for the cases to sit on. The straps are used to just hold then against the panel.

Neat idea! Thanks for sharing

Howard · Nov 24, 2025

I didn't realize there was that much room behind the seat. How thick are your cases? I need to do something similar rather than stacking loose items behind the seat.

DIY - Molle Panel Behind Back Seat

Thex

Well-known member

Angmar

Member

Thex

Well-known member

Bobby Chapman

Well-known member

Escapologist

Well-known member

Little boy blue

Well-known member

Alfetta159

Well-known member

Thex

Well-known member

Thex

Well-known member

Thex

Well-known member

Escapologist

Well-known member

Cancunbadlands

Well-known member

RR - All the way

Well-known member

Marshall

Member

Howard

Well-known member

Similar threads