New Phone Mount Option from Course MotorSports

[Lynyrd Skynyrd]

Looks like it is available for purchase now. I am interested but don't want to be a guinea pig. I have a phone holder from Etsy that goes in the fits cubby but it is too loose. Maybe I am too picky

If you like the holder you have and leave it in all the time, put bits of butyl rubber around it. A tiny bit goes along way and can also fix leaks, rattles, house ductwork leaks, gutter leaks etc and is totally removable anytime. Here’s a roll for 14 bucks

Sponsored

 

[Dad]

Most basic trim removal kits will have one like that, like this kit

https://a.co/d/bWrb9BJ

Harbor Freight has them as well.

 

[Lynyrd Skynyrd]

Edit. See below for name made fix
Hope they have a return policy. I took one for the team. It may work with a small phone but not a 14 pro max. If you watch the installation video it shows to mount the clip right over the radio green clip(center). I bought the mag fit and the cradle. One was gonna be for GF to charge her phone.
1. the mount clip is loose because the radio does not fully seat. See the pic of the gap on the right side. The gap wouldn’t bother me if it was solid and not vibrating when driving. The self stick tape is not strong enough to hold it.
2. The phone touches the tuning knob with either mount. Because it vibrates the phone bounces off with the mag mount while driving unless you tilt it up and away. The cradle mount does not drop the phone but sits to low. Tilting phone in awkward direction is not acceptable.
3. The phone holder clip. if I slide it up does not allow the radio to seat at all. Not much wiggle room.

 

[Mavreezy]

Hope they have a return policy. I took one for the team. It may work with a small phone but not a 14 pro max. If you watch the installation video it shows to mount the clip right over the radio green clip(center). I bought the mag fit and the cradle. One was gonna be for GF to charge her phone.
1. the mount clip is loose because the radio does not fully seat. See the pic of the gap on the right side. The gap wouldn’t bother me if it was solid and not vibrating when driving. The self stick tape is not strong enough to hold it.
2. The phone touches the tuning knob with either mount. Because it vibrates the phone bounces off with the mag mount while driving unless you tilt it up and away. The cradle mount does not drop the phone but sits to low. Tilting phone in awkward direction is not acceptable.
3. The phone holder clip. if I slide it up does not allow the radio to seat at all. Not much wiggle room.

Not feeling that huge gap...

 

[Mavreezy]

Thanks for taking one for the team. You saved my ass some flow...

 

[Lynyrd Skynyrd]

So I got it to work by just screwing their clip to the inside the cubby. Rock solid works like a champ. I’m going to see if I can talk to them and fix this issue. I was gonna modify the clip as half is not needed but I don’t see it and don’t care enough.
The magnet mount works fine this way, does not fall off over bumps.
The cradle mount is pretty cool as it automatically closes and to open a light touch of a switch. See video

 

[Hammer]

So I got it to work by just screwing their clip to the inside the cubby. Rock solid works like a champ. I’m going to see if I can talk to them and fix this issue. I was gonna modify the clip as half is not needed but I don’t see it and don’t care enough.
The magnet mount works fine this way, does not fall off over bumps.
The cradle mount is pretty cool as it automatically closes and to open a light touch of a switch.

 

[Hammer]

My experience …. I installed yesterday. I removed the small square rubber bumper with the self-adhesive strip since that’s what the install video called for. I did have a hard time getting the screen to snap fully back into place on the right side where the ball mount attaches, but after a few minutes was finally able to get it snapped and it’s now snug. I placed the magnetic piece on the lower part of my phone so it sits up a little higher and doesn’t interfere with the tune knob. Overall I’m happy with the setup

 

[Lynyrd Skynyrd]

My experience …. I installed yesterday. I removed the small square rubber bumper with the self-adhesive strip since that’s what the install video called for. I did have a hard time getting the screen to snap fully back into place on the right side where the ball mount attaches, but after a few minutes was finally able to get it snapped and it’s now snug. I placed the magnetic piece on the lower part of my phone so it sits up a little higher and doesn’t interfere with the tune knob. Overall I’m happy with the setup

Looks like the gap is still there? I tried and felt it would break if I pushed further.
also the 14 pro plus uses MagSafe where the height is not adjustable and can’t use the metal plate. Glad it worked for you

 

[Hammer]

Looks like the gap is still there? I tried and felt it would break if I pushed further.
also the 14 pro plus uses MagSafe where the height is not adjustable and can’t use the metal plate. Glad it worked for you

The gap is essentially the same as the driver side and it’s fully snug so I’m satisfies that it’s okay. The one big difference I have from your setup is that I have the iPhone SE which is a lot smaller than your 14 pro plus and I can see where that would pose the issue that you identified. Your workaround is good.

 

[crunchie_frog]

Thank you @Lynyrd Skynyrd

 

[Tetochibichu]

So I got it to work by just screwing their clip to the inside the cubby. Rock solid works like a champ. I’m going to see if I can talk to them and fix this issue. I was gonna modify the clip as half is not needed but I don’t see it and don’t care enough.
The magnet mount works fine this way, does not fall off over bumps.
The cradle mount is pretty cool as it automatically closes and to open a light touch of a switch. See video

I love the phone ception you did there. A picture of a picture of a phone mount. The other phone needs a picture too.

Have you tried mounting that bracket over the top lip and bolt it from behind out of view?

 

[Jared83]

Edit. See below for name made fix
Hope they have a return policy. I took one for the team. It may work with a small phone but not a 14 pro max. If you watch the installation video it shows to mount the clip right over the radio green clip(center). I bought the mag fit and the cradle. One was gonna be for GF to charge her phone.
1. the mount clip is loose because the radio does not fully seat. See the pic of the gap on the right side. The gap wouldn’t bother me if it was solid and not vibrating when driving. The self stick tape is not strong enough to hold it.
2. The phone touches the tuning knob with either mount. Because it vibrates the phone bounces off with the mag mount while driving unless you tilt it up and away. The cradle mount does not drop the phone but sits to low. Tilting phone in awkward direction is not acceptable.
3. The phone holder clip. if I slide it up does not allow the radio to seat at all. Not much wiggle room.

Is that still wired carplay?

 

[trucklover86]

I have a phone mount from CourseMS for my Subaru Crosstrek and really like that it attached via the trim, not blocking a vent or having to stick anything on. I signed up to be notified when they have something available for the Maverick and got the email today!

Here's a link to the installation video:

And here's a link to their website for the Maverick for pre-orders: https://coursemotorsports.com/collections/ford/products/direct-fit-phone-mount-ford-maverick-2022

Do they ship to canada ?

Sponsored