Finally bought one. 2025 tremor

[FERALMAVERICK]

Share a night picture with the Raptor lights on!

Sponsored

 

[JasonDroninAround]

The black is beautiful but I'm kind of glad I got 'stuck' with a white one. I have too many pin stripes for only owning it for 7 months hehe

 

[Cancunbadlands]

Perfect! I might order those! TY

 

[ReddWulf]

f150led.com , if u have a 25+ you will have to cut and mod them to fit flush or correctly . 22-24 are direct fit

What were the cut and mods you had to make? I still haven’t found a direct fit for my 25 Tremor, even though the grill seems custom made for it. Thank you.

 

[FERALMAVERICK]

What were the cut and mods you had to make? I still haven’t found a direct fit for my 25 Tremor, even though the grill seems custom made for it. Thank you.

you will have to sand the sides down and round the corner in the front to get it to sit flush, i also put another piece of 3m red stripe tape on it to get them down so they were more in the opening, sry wish i would of taken pick as i did it . ill try and get some pick up in the grill

 

[ReddWulf]

you will have to sand the sides down and round the corner in the front to get it to sit flush, i also put another piece of 3m red stripe tape on it to get them down so they were more in the opening, sry wish i would of taken pick as i did it . ill try and get some pick up in the grill

No worries, thank you for the reply. I’m on the hunt for a good solution for the 2025 (and I assume 26) Tremor grille. I even reached out to F150LED about the different dimensions they have. Yours is the closest I have seen, they look great and exactly what I’m looking for. If it really is just a bit of sanding, it may be the best option. Just didn’t want to commit if it involved a lot of cut and grind on a new set of lights/truck. Thank you!

 

[FERALMAVERICK]

No worries, thank you for the reply. I’m on the hunt for a good solution for the 2025 (and I assume 26) Tremor grille. I even reached out to F150LED about the different dimensions they have. Yours is the closest I have seen, they look great and exactly what I’m looking for. If it really is just a bit of sanding, it may be the best option. Just didn’t want to commit if it involved a lot of cut and grind on a new set of lights/truck. Thank you!

if you opt to do them , its not horrible to do and the only truck mod is u have to drill a hole to get the harness threw but not noticable . pm me if do them and need some help. a dremel witha sanding drum and some silicone makes it way easier ..

 

[JasonDroninAround]

I still say my most favorite mod for my Tremor was also the cheapest. It's that little plastic button cover that covers the buttons on the center console. I keep my wallet in my front pocket and my wallet kept turning the traction control on and off after I put it four wheel drive

 

[Cancunbadlands]

I still say my most favorite mod for my Tremor was also the cheapest. It's that little plastic button cover that covers the buttons on the center console. I keep my wallet in my front pocket and my wallet kept turning the traction control on and off after I put it four wheel drive

So I can find the start button easily...

 

[FERALMAVERICK]

So I can find the start button easily...

I like that its clean and simple

 

[ReddWulf]

I like that its clean and simple

Yeah, I must admit I have turned my radio off a couple of times already with the 25 knob being right above it!

 

[FERALMAVERICK]

A few updates and changes

 

[FERALMAVERICK]

Zone level and bfg ko3 245/70-17

 

[FERALMAVERICK]

Cleaned it up after new parts. Hiking and exploring

 

[Meeka]

Cleaned it up after new parts. Hiking and exploring

Nice! Looks like the KO3’s have a different tread pattern than the KO2’s, which had the same pattern for years.

Sponsored