2024 XLT FX4 Azure Gray Build

[Nessus]

Put the gloss black door handles on and the Mabett side markers on. Now I gotta figure out a phone mount. My first Amazon try was a bust

I just bought a 2024 XLT FX4 and bought a "phone holder" on Amazon. First a cube that was supposed to fit in the space on the dash that had a bunch of crossbars on it to attach the phone holder to. Didn't work.

Sponsored

 

[Superg0]

I just bought a 2024 XLT FX4 and bought a "phone holder" on Amazon. First a cube that was supposed to fit in the space on the dash that had a bunch of crossbars on it to attach the phone holder to. Didn't work.

I have this exact cubby gadget. I had to use double sided tape to secure it but it works fine now.

 

[Superg0]

Bought some blue vinyl, its not an exact match but I think it complements the Azure Grey. My hood has been redone at least 7 times....

 

[TORQUERULES]

UPDATED with most recent pics and accessories

Picked up my XLT FX4 Azure Grey Maverick on Friday after a 3 month wait. Had a stack of parts ready to go and started to build it up immediately.

Parts so far
Thermal R&D Catback Turndown Exhaust
Air Design front spoiler
UPR Clean and Dirty side catch cans
Mabett Side Markers
JB4 with wireless kit
Gloss Black front grill trim
Gloss Black rear Ford emblem trim
Vvivid Vinyl hood
Focal RSE Speakers, MTX 8" speaker
Gloss Black door handles
3D Maverick Tailgate lettering
Matte black fuel door
S&B intake
Painted tow hooks
painted brake calipers
Rough Country tri fold
Mabett seat covers
Paddle shifter steering wheel

Any tips on the front spoiler install? I am getting ready to do mine.

 

[Superg0]

Any tips on the front spoiler install? I am getting ready to do mine.

A couple of things I ran into was temperature, and adhesive related. I bought my Mav in the spring when temps were not really warm enough to cure overnight. Make sure you either apply in a heated environment or when the temps are warm enough. Apply the adhesive very liberally. My first attempt didn't take and I had to reapply.

 

[TORQUERULES]

A couple of things I ran into was temperature, and adhesive related. I bought my Mav in the spring when temps were not really warm enough to cure overnight. Make sure you either apply in a heated environment or when the temps are warm enough. Apply the adhesive very liberally. My first attempt didn't take and I had to reapply.

Thanks. My garage is heated, so I was planning on letting it sit for at least 3 days after installation in 70-75 degree heat.

 

[Superg0]

Thanks. My garage is heated, so I was planning on letting it sit for at least 3 days after installation in 70-75 degree heat.

My garage is not heated and the adhesive never really took. I also did not put enough adhesive on so within days it was coming off in places. I reapplied and put on much more adhesive...much more than the first time. Luckily the old adhesive never really stuck so pealing it off was easy. Hasnt moved now at all.

 

[TORQUERULES]

My garage is not heated and the adhesive never really took. I also did not put enough adhesive on so within days it was coming off in places. I reapplied and put on much more adhesive...much more than the first time. Luckily the old adhesive never really stuck so pealing it off was easy. Hasnt moved now at all.

As in much more adhesive... How much more than Air Design's instructions?

 

[Superg0]

As in much more adhesive... How much more than Air Design's instructions?

I completely used up all the included tube of adhesive between both attempts. I would imagine using almost an entire tube for a correct adhesion.

Sponsored