Search results

I haven't found one thats definite, but I did run across these steps: From Configuration and Programming ->As-Built Configuration -> Load Factory AsBuilt Please note that you need be connected to the internet to do this. You can also FIle -> Open -> saved backup, then write back.

I did so many mods to both of mine... First on both were the tailgate letters. Both are now similar in things done: Tailgate letters cab & tailgate spoilers fender flares (1 has AirDesign, other has Bushwhacker) hood protector Lasfit LED lighting RGBIC cargo bed lighting 23 got the JOB1 climate...

I don't do batch files as the app itself doesn't provide a consistent interface (sometimes the order of things is different, so even a "Sendkeys" script would mess up). However, there are a few places to get started: ForScan, Programmers, Tuners, Coders | MaverickTruckClub - 2022+ Ford Maverick...

That bed extender is made by Lund. Have you tried to contact Lund for just the mounting hardware? LUND® | Lund Truck

Here's the two settings (under the ABS Module): After changing the two settings in red above, be sure to click the Write button at the bottom and close the service procedure, then turn the Mav off and back on again.

If you go this route, I wanted to share some info on past experience: 1. Look up your state law on when a vehicle becomes eligibile, and use that phrasing when talking to ford Customer relations. i.e. if it says "out of service for more than 30 days", make sure you say "it has been out of...

I use one of these in both Mavericks: https://www.amazon.com/Ottocast-Wireless-Android-Adapter-Plug/dp/B0BGS8X66Y They are a bit finicky trying to update the firmware, but if you can get that done, they work great. It takes a few seconds to connect after the radio comes on, but otherwise its...

I had the tape/glue at the ends on mine. I trimmed off the last 3 inches, re-prepped with 3M 4298 Adhesive Prep and used some 3M VHB tape to re-attach. It has held quite well through the last month or so for me out on the east coast.

I seem to recall reading somewhere that on 22s, you could disable the popup, but you can't on 23s. I am going to take some time to dig in to ForScan and options comparisons between both of mine to see if there might be something, but I doubt it given what I've heard already. If I do find...

I would recheck the fuse you tapped for ACC. From your statements: - When I connect the camera with the supplied power cord the camera switches on and off with the ignition switch. - When I power the camera using the smart hardware kit the power only comes on when pressing the power button on...

What drew me into it was a customer at the time who required all field service agents have a UHF/VHF radio to communicate when working in the California and Arizona deserts as some of their facilities did not allow cell phones (i.e. secured locations - no devices with cameras, memory storage)...

I use my Midland 75-822. Its a handheld that fits in that same mount. It offers the ability to also use an external antenna if I want as it comes with a cable/adapter. I am still trying to figure out how to make the mount work while using that configuration. I personally don't run an external...

Attached is the current iteration of the mount. Its the same mount for all 3 radios. All you need is a cubby mount with the FITS connector. I am still tweaking it a bit to better accommodate one radio with a longer antenna. Once I get it worked out, I will upload that version.

Yes. At this point, both my FE and Tremor have identical values and everything works in both.

I am not near you,. but I added it to mine. It was pretty easy. You have to change 2 values: SDM - ABS change from enabled to disabled SDM - Sport change from disabled to enabled When I first added it, I missed changing the ABS one so the modes were there but I got messages they were not...

The Alter Ego Twins side by side in the driveway: 22 Rapid Red Hybrid & 23 Atlas Blue Tremor Always fun to see them paired up. And this reminds me, I gotta mow/trim/edge the yard today LOL

Updated with recall notice: I went to go get the Sync software update for a manual install. It was clear then. After the install when I went back to the site to upload the XML file, I had a recall appear.... Its almost a week old since it's issue date even though it only showed up today...

I got to thinking and I wanted to add this to further add weight to the possibility it might be diseling: Listen to the original poster's 4th video at the end and note the sound. Then listen to this video of an old Dodge D1 dieseling: Gas engine dieseling doge d100 - YouTube The first 30...

My take is that we need more people to test things to rule out as many possibilities as we can, and changing gas stations is probably the least intrusive. What we know: The engine is continuing to cycle for a second or two or even longer after the ignition is cut. Others in the thread have...

Maybe not the best way to say it, but when it goes from gas side shutting down to only electric.