Search results

While I had the truck apart for more sound deadening, I decided to go ahead and replace the B&O speakers all around. Overall a good improvement in sound quality. In the front: Focal RSE165 Auditor from Crutchfield Center: Infinity Reference REF-3032CFX Rear: Infinity Reference 6432CFX For the...

Taking a break from sound deadening to get the truck undercoated. Went to friend's house with a lift and removed all bottom panels and sprayed CRC Corrosion Inhibitor on all body surfaces. Used 6 cans. Marine grade stuff so hopefully will last. On top of that we sprayed about 2 gallons of...

Got the under seat storage bins done as well. Same Kilmat and closed cell foam. The bins needed a little encouragement going back in but no more noise coming from there anymore. Also was able to get into the rear foot wells where there is some foam that does not always sit flush to the carpet. A...

Now jumping into the sound deadening of the project. This was the most time consuming part of the whole build. Probably spent over 100 hours covering everything I could get to. Unfortunately, I didn't get a before measurement for sound level comparison, but I am extremely satisfied with the...

I don't have pictures of it but there are three pieces. One is the clear plastic lens that can be pryed out but unsure now which side you pry from and if that matters. Once you remove that there are two more pieces plus a spring used for pressing the light as a button so make sure to keep track...

It's really hard to tell but I would say just slightly. I think most people would say the shine comes from the polishing and wax (if you didn't ceramic coat) and ceramic coating is the protection part. Carpro Gliss is supposed to be the ceramic topcoat that sheds water like crazy. I did notice...

Next addition was Lasift LEDs all the way around. Great improvement over stock. Very bright and love the instant on/off. Makes the truck feel like a higher trim. Turn signals seem to have a wide angle though so I hope it's not too bright. When pulling up to an intersection, I can see a...

I have towed this 5x10 ft enclosed trailer several times now and the truck feels great especially in tow mode. This project was buying 38 bales of fiberglass blown-in insulation (2 pallets) and the rental blower machine from Home Depot.

Next mod was in the bed adding a 12v panel to the right cubby. I used the included Ford flex bed wiring adaptor to plug into the right flex bed power adaptor. I wanted the panel to be hidden in the cubby so I could still use the cubby normally for storage and make everything look clean. The...

Added the auto-dimming KIA mirror that everyone has. I ordered it well after the craze and had no issues from the KIA parts place after I provided a VIN from the internet. Hardwired from the fuse box 12V, ACC, and ground. I used fuse #3 for ACC, #20 (spare) for 12V. Ran 16awg stranded wire...

Added the Ford oem chrome tailgate lettering, tailgate assist, chrome ford door sill plates. Removed dealer installed sticker. Installed the Bakflip MX4 hard trifold tonneau cover from Realtruck using forum pricing ($850ish at the time). Love the low profile look of the Bakflip. I was looking at...

Within three weeks of taking delivery, I applied two coats of Carpro Cquartz 3.0 ceramic after decontamination wash, some claying, and polishing. I did not polish the entire truck because I found that I was putting more scratches on than I was taking off. So I gave up and just went for it. I did...

Hi everyone, I'm starting this build journal to document everything I've done to my truck since the list is getting longer and longer. I took delivery of my Maverick on 9-30-22 from Lakeview Ford Lincoln in Battle Creek, MI. My build was a 2022 Alto Blue Lariat Lux with FX4, Tow package, and...

Adding this picture for reference where the factory inverter is located. Underneath the center console and pretty easy to get at. Only two trim pieces and a few bolts required to remove.

I dropped the headliner for sound deadening. Two clips in the back plus all of the pillar trim hold it up.

Old thread, but I wanted to post what I have researched because I was considering this mod. The Maverick cupholder part # LJ8Z5813562AA is shared with the Bronco and Mach e. On the bronco forum, this thread goes into how to swap in a lighted cupholder assembly from the Lincoln Corsair. This part...

This would totally work on the Maverick. The lane centering requires a small resistance on the wheel when it moves to think you still have your hands on the wheel. If you hold the wheel too lightly going down the road it will still complain. I haven't tried this weight hack but I'm sure it work...