Cubby FITS Slot + Some other 3D print designs

[Kl0ck]

I've been working on some enhancements / tweaks to existing designs to suit them to my purposes and recently added a few custom ones (FITS slot for the cubby, HAM Radio stand). I'm currently working on a semi-generic phone holder for my work phone and some on the door FITS slots for holding a flashlight, glass breaker, etc.

If you've got any ideas, please share and I will take a crack at them!

-- 02/12/2022 -- Added Pixel 3 / 4 Phone Holder STL
-- 02/14/2022 -- Added Pez Dispenser for @Randy H. LOL
-- 02/14/2022 -- Added Midland Radio Mic Mount for @BlackhawkBen
-- 02/14/2022 -- Added Paper Towel Holder for @Clarkdonbran
-- 02/14/2022 -- Added Umbrella Holder for @WasChops
-- 02/14/2022 -- Added Sunglasses Holder for @brkr12002
-- 02/14/2022 -- Added Flashlight charger plate for @TCK
-- 02/18/2022 -- Added Seat Hooks and FITS backseat bar for @WannaMav

Link: My Thingiverse
Link: My Printables

-Cubby FITS-

-Cubby Blank-

-Baofeng UV-82C Holder-

-LP Cupholder with Cable Organizer-

-Pixel Phone Holder-

-Behind the seat clips + bar for FITS slot-

Sponsored

 

[Randy H.]

I want a Cubby PEZ dispenser. But could use a 3D printed insert to hold my garage door opener...
Basically the blank off you have with a slot to slide the garage door opener clip into.

 

[Kl0ck]

I want a Cubby PEZ dispenser.

I think this should fit the bill? I have a Darth Vader Pez, will test once I print it out.

FITS Pez Dispenser

 

[Kl0ck]

Basically the blank off you have with a slot to slide the garage door opener clip into.

The dimensions internally within the cubby space shrink as you reach the back - It is sloped at the bottom. This makes filling the space (as with like a cup or box) hard - I haven't cracked it yet.

I came up with this that basically does the same thing but in the opposite way:

You would slide the clip for your garage door opener over the bar and then slide it in as one piece. This does the same thing - hides the garage door opener in the cubby and keeps it hidden via the face plate.

Garage Door Opener Holder

 

[tonyfall1]

I posted this in another thread. I thought it was a good idea.

 

[Kl0ck]

Yeah man that is a good idea. I'll have to work on what angle he makes his slopes at, but I like the grid idea for sure - lots of compatibility.

I did a quick mock up against his design - I don't think its deep enough thus the bottom and top feet but it might work for a few chargers - then again for $20 might just be worth buying that one if you have those kind of phone holders already

Threw it up on thingverse : The Grid

 

[MaverickHybrid]

I want one!

 

[BootXL76]

So this is a long shot, but if somebody, anybody can somehow design a piece to replace this: where that that cubby/slot is inverted

I’d pay handsomely for quality/color matched, etc

 

[Dad]

I posted this in another thread. I thought it was a good idea.

Great idea!

 

[MaverickHybrid]

Not the best thread to ask but What are the options to add a power outlet inside that useless cubby?

 

[Clarkdonbran]

I’d like a vertical paper towel roll holder for the rear FITS.

 

[HotJombalya]

I've been working on some enhancements / tweaks to existing designs to suit them to my purposes and recently added a few custom ones (FITS slot for the cubby, HAM Radio stand). I'm currently working on a semi-generic phone holder for my work phone and some on the door FITS slots for holding a flashlight, glass breaker, etc.

If you've got any ideas, please share and I will take a crack at them!

Link: My Thingiverse

-Cubby FITS-

-Cubby Blank-

-Baofeng UV-82C Holder-

-LP Cupholder with Cable Organizer-

These are awesome! Thank you! I bought a Creality CS-6E (or something like that) in anticipation of the FITS stuff and it turns out it’s hard to come across files out there. I’m going to print some of these and will post the results!

 

[BlackhawkBen]

Awesome work so far, I have an idea for you, I want to mount a Midland MXT275 in my truck hidden and have a mounting plate for the microphone to mount with a Keystone Jack underneath so I can extend with Cat5 and easily move and hide when needed, also if there is a slot for the extra cabling to tuck in bonus but not necessary. Ideally easy to remove with 2 or 4 screws

For more clarification: https://midlandusa.com/collections/micromobile/products/mxt275-micromobile-two-way-radio

Picture of Midland Mic:

Picture of Keystone Jack Port Back:

 

[projectvortex]

I want a Cubby PEZ dispenser. But could use a 3D printed insert to hold my garage door opener...
Basically the blank off you have with a slot to slide the garage door opener clip into.

Make mine a Xanax dispenser so “build date fright” will be easier to take.

 

[bombast]

Not the best thread to ask but What are the options to add a power outlet inside that useless cubby?

That would likely involve a bit of drilling and a whole lot of ripping the dash out.

Sponsored