Search results

Thanks! Unfortunately I live about 6 hours away from the dealership, but I will follow another poster's advice and get video evidence that the Pulse is not working. I may also take it to my local dealership and have them verify whether or not it was actually installed. Then, I'll take that...

Thanks for this advice! I will try this, I think is is probably the best option. I live 6 hours away from Wade Ford, otherwise I'd just go on down there and ask them to check it out. I've also given Wade Ford a call and am waiting for their GM to get back to me.

Hello all, I purchased my 2022 hybrid Ford Maverick XLT in February 2022, off the lot (no preorder) from Wade Ford in Smyrna, GA. At the time the dealer markup was not too bad, but they also tacked on two charges for dealer extras: $200 for etching my windows with my VIN, and $600 for the Pulse...

I see how you have this in here, but it seems to me that if you actually use it as a tie down, all the force of the weight is going to be levered against your tailgate (with the tailgate acting like a fulcrum), and applying serious pressure to your bolt. Any reason you didn't put it up on the...

Overall, I do really like the bak X4S cover. I wish it was a bit more water tight. Because of the 1/8 in aluminum shims I had to install under the rails, I get a little leaking of water up towards the cab when it rains. So far it hasn't been a big issue, if I need something dry I either put it...

Good thing that's a rare occurrence, eh?

No... It's only "in the event of an engine failure" so, not the cat.

I'll be honest, I'm trying to change my oil right now, the 74 MM oil change filter doesn't work. Even though that's what motocraft says you need. I literally cannot loosen this factory tightened filter.

Thanks! This worked perfectly. Got two 4' x 1.5" aluminum flat bars at 1/8" thick. I put one on each side and it works perfectly, although it was harder to get the clamps to hold it securely. I'm still not 100% on the fit - the front looks kind of crunched together, and the vinyl definitely...

Thanks! I think I figured out the first issue with the foam. I put my strip a little bit to centered on the bulkhead, so I use a couple short pieces for where the bed rails meet the bulkhead. As for the second issue, the groove's not aligning, I'm going to shim one of the rails by 1/8" to see...

Thanks! I am at the hardware store now getting some 1/8" aluminum shims. When you say shim the cover, I'll have to loosen the bed rails as well, because the shim will serve to push the bed rail into the bed, correct? Wish me luck! I wish home Depot had 1/16" aluminum flat bars...

Hey man, I was wondering if you had a minute, can you tell me if you are having this issue with your rollup cover? It seems like each rail has a "groove" that the cover latches are supposed to fit into. But with mine, when the driver's side is "in the groove", the passenger side rides the...

Hey man, I was wondering if you had this issue with your X4S as well. The underside latches for the rolling cover seem to want to sit in these "grooves" in the bed rails, but unfortunately for me the cover only allows one side to fit in the groove - and then the whole cover is "crooked". Do both...

So I removed everything and put in some more foam, so I think I may have solved the finger gap issue. However, has anyone else seen that the width doesn't seem to be perfect? This is my driver's side, as I unroll the cover - the 1/8" space and the cover latch seems to fit nicely in the rail...

So when you installed the foam pad, did you put it right up "flush" with the end of the bulkhead? The instructions seemed to leave a bit of a gap between the edge of the bulkhead and the foam... I'm having trouble getting mine to properly seal (see my post here). I don't know if I should try to...

Hello all, I read one other thread where something like this was happening but wasn't sure if I am doing something incorrectly. I have the SIBL and installed the bed rails square (as close as I could get it) and flush towards the cab as far as I could go. However, there's a clear gap in the...

These are actually more than just bottle openers - they are tie down points as well.

To each his own, I suppose. I hate the sloped curves of the Santa Cruz.

Thanks!

Hey, so I'm in the same boat as you. Same truck and everything lol. Having trouble figuring out the fuse box - is it under the hood, or inside the cabin? If it's under the hood, how do you run wires from the hood into the cabin? Debating getting the OBD power cable to just skip the fuse box...